Strength by Nature.
Performance by
Science.
We make products that work better and last longer.
Real solutions for real projects, built with clean design
and honest mineral-based materials.
One bottle of GEO-SIL™ covers approximately 150 square feet, depending on the spray rate.......
Engineered for Long-Term Surface Protection
GEO-SIL™ is a reactive silicate-based surface treatment designed to penetrate deep into concrete and masonry substrates, forming a permanent mineral structure that improves durability and resistance.
Stronger surfaces
Enhanced structural stability
Reduced porosity
Where Sustainable
Engineering meet
Reactive Performance
GEO-SIL™ transforms naturally occurring silicates into high-performance surface treatments that chemically bond with concrete, stone, and mineral substrates. The result is a permanent crystalline matrix that increases hardness, reduces porosity, and extends material life.
- Mineral-reactive chemistry
- Permanent densification
- Deep substrate penetration
- Zero peeling, zero delamination
- Industrial-grade durability
EASY APPLICATION
1.
Surface Preparation
- Clean Surface: Remove dust, oils, coatings & debris
- Achieve Correct Profile (ICRI CSP 2–4)
- Saturated Surface Dry (SSD)
2.
Mixing / Dilution
- Shake or Stir concentrate
- Add Concentrate to DI or distilled water
- Mix Thoroughly
Use Within 7 Days
3.
Application
- Low-Pressure Sprayer, roller, or brush
- Work in 100–150 sq ft sections
- Keep Surface Wet 5–10 minutes
4.
Cure Time
- Light Traffic 4–6 hours
- Full Cure 12–48 hours
- Topcoat (if needed)
5.
Post-Application Inspection
- Check Appearance & sheen
- Perform Water Drop Test
- Water Beads Up (no absorption)
- Document Results
CORE BENEFITS
Long-term surface strengthening
Resist water penetration
UV & weather durability
Breathable protection (no sealing trap)
Invisible finish
Low maintenance solution
Industrial-grade performance
Long-lasting effect, 2–5 up to 7 years depending on surface and usage
Designed for Multiple Surface Types
" alt="Concrete Floors">
Performance Outcomes
Quantified improvements after a single GEO-SIL™ application
| Property | Untreated Concrete | After GEO-SIL™ |
|---|---|---|
| Water Absorption | High (capillary suction) | Reduced by up to 90% |
| Surface Hardness | Baseline | Increased 15–25% |
| Abrasion Resistance | Baseline | Improved significantly |
| Water Contact Angle | ~30° (wettable) | >110° (non-wettable) |
| Vapor Transmission | Open | Retained (breathable) |
| Chlorine Salt Resistance | Low | Improved significantly |
| Dust Generation | Significant | Eliminated |
| Penetration Depth | N/A | 3–6 mm |
| Bond Type | None | Covalent Si–O–Si |
Frequently asked questions
How can I make the GEO-SIL solution work most effectively?
The concentrate MUST be mixed with a gallon of DI/Distilled water and mixed. It should be used within 7 days of mixing.
Can I apply the concentrate directly on the substrate to get better results?
No. It will not work and might stain or ruin the substrate. The concentrate cannot be used directly on the substrate.
What if I use less than a gallon or more than a gallon of DI/DISTILLED water?
The concentrated formula is formulated for a gallon of DI/Distilled water. It has a tolerance of ±2% only. We highly recommend using a gallon of water.
What if I use well water or city water instead of DI/Distilled water?
It will work, but the product's performance might be compromised. We highly recommend using DI/Distilled water.
What if I use hard water or well water that has high amounts of salts?
The product performance might diminish greatly.
What if I use chlorinated water?
The product performance might diminish greatly.
Which substrates are ideal for GEO-SIL?
It works on most porous substrates. For example, concrete, pavers, bricks, and stones.
Can it work or be applied on painted porous substrates?
No.
Can it work on wood?
No.
What type of surface preparation do I need to do before applying DILUTED GEO-SIL?
The surface should be cleaned with pressure washing and dried fully before applying it. Please refer to the Technical Data Sheet (TDS) and Product Application Guide for the complete details
Can it be applied to wet surfaces?
No. The surface needs to be dry.
What will be the ideal temperature window to apply GEO-SIL?
PARAMETER ------------------------------ ACCEPTABLE RANGE
Ambient Temperature ----------------------40°F–95°F (4°C–35°C)
Surface Temperature -----------------------40°F–120°F (4°C–48°C)
Relative Humidity --------------------------- 20%–90% (non-condensing)
Wind Speed (outdoor) ---------------------- < 15 mph to prevent premature surface drying
Substrate Moisture -------------------------- Damp to SSD (not wet, not puddled)
How long does it take to cure?
12-24 hours.
What is the coverage of the Geo-Sil surface treatment solution
Approximately 150-175 sq. ft per bottle/per gallon. It may vary based on the application rate.
How long does it last?
2-5 years depending on thesurface and usage.